HUAWEI

S5720-28P-PWR-LI-AC Huawei S5720 24-Port Gigabit POE Switch+ 4 SFP Port

  • S5720-28P-PWR-LI-AC Huawei S5720 24-Port Gigabit POE Switch+ 4 SFP Port
  • Description
  • Specification


1

Twenty-four PoE+ 10/100/1000BASE-T ports

2

Four 1000BASE-X ports

Applicable modules:
  • GE optical module
  • GE-CWDM optical module
  • GE-DWDM optical module
  • GE copper module (works at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s)
  • Stack optical module (only used for stack connection)
  • 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables (only used for stack connection)
  • 3 m and 10 m AOC cables (only used for stack connection)
  • 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking, supported in V200R011C10 and later versions)
  • H87MMA5671A2 GPON optical module (applicable in V200R012C00 and later versions)
A license can be activated on the switch to increase the speed of the four optical ports to 10 Gbit/s. Applicable modules:
  • GE optical module
  • GE-CWDM optical module
  • GE-DWDM optical module
  • GE copper module (only 1000 Mbit/s supported)
  • 10GE SFP+ optical module (OSXD22N00 not supported)
  • 10GE-CWDM optical module
  • 10GE-DWDM optical module
  • 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables
  • 3 m and 10 m AOC cables
  • 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking, supported in V200R011C10 and later versions)
  • H87MMA5671A2 GPON optical module (applicable in V200R012C00 and later versions)
NOTE:

If a port uses a GPON optical module, other 1000BASE-X optical ports cannot be used.

3

One PNP button

NOTICE:

Applicable in V200R012C00 and later versions:

To restore the factory settings and reset the switch, hold down the button for at least 6 seconds.

To reset the switch, press the button.

Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.

4

One console port

5

One USB port

6

Ground screw

NOTE:
It is used with a ground cable.

7

RPS socket

NOTE:

It is used with an RPS cable, which is not hot swappable.

8

Jack for AC power cable locking strap

NOTE:
The AC power cable locking strap is not delivered with the switch.

9

AC socket

NOTE:

It is used with an AC power cable.

-

-

Product Name
Huawei  S5720-28P-PWR-LI-AC Switch
Uplink Interfaces

24 10/100/1000 base-t Ethernet ports +4 gigabit SFPS

Switch Capacity
336Gbps
Packet forwarding rate
51Mbps
MAC Address Table
16K
Dimensions (W x D x H)
442×220×43.6mm
Rated voltage range
100-240V AC,50/60Hz
Relative humidity
5%-95% RH
Operating temperature
0-45℃
Power Consumption
370W


Previous: Huawei S5720S Series Switch S5720-28X-LI-AC 24 Port Gigabit ...

next: Huawei S5710-52X-LI-AC 48 Gigabit Ethernet Ports, ,4x 10G SF...

Top

Cisco network switch,Huawei switch,Cisco Router, Huawei router,NEW used Cisco comparison, Huawei AP WeChat Code

Copyright © 2018 - 2019 Shenzhen Bo-Net Technology Co., Ltd. All Rights Reserved.