HUAWEI

Huawei S5730-SI Series Switch S5730S-68C-PWR-EI 48 PoE+ 10/100/1000BASE-T ports

  • Huawei S5730-SI Series Switch S5730S-68C-PWR-EI 48 PoE+ 10/100/1000BASE-T ports
  • Description
  • Specification

1

Forty-eight PoE+ 10/100/1000BASE-T ports

2

Four 10GE SFP+ ports

Applicable modules and cables:

· GE optical module

· GE-CWDM optical module

· GE-DWDM optical module

· GE copper module (100M/1000M auto-sensing)

· 10GE SFP+ optical module (OSXD22N00 not supported)

· 10GE-CWDM optical module

· 10GE-DWDM optical module

· 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables

· 3 m and 10 m AOC cables

· 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking)

3

One ETH management port

4

One PNP button

NOTICE:

Applicable in V200R012C00 and later versions:

To restore the factory settings and reset the switch, hold down the button for at least 6 seconds.

To reset the switch, press the button.

Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.

5

One console port

NOTE:

It is used with a console cable. The console cable is not delivered with the switch and needs to be separately purchased if needed.

6

One USB port

7

Ground screw

NOTE:

It is used with a ground cable.

8

ESN label

NOTE:

You can draw it out to view the ESN and MAC address of the switch.

9

Rear card slot

NOTE:

Card supported:

· ES5D21Q04Q01

· ES5D21VST000 (applicable in V200R012C00 and later versions)

10

Fan slot

NOTE:

Applicable fan module: FAN-028A-B

11

Power module slot 2

NOTE:

Applicable power modules:

· 500 W AC PoE power module

· 650 W DC PoE power module

· 1150 W AC PoE power module

· 1000 W AC PoE power module (applicable in V200R013C00 and later versions)

12

Power module slot 1

NOTE:

Applicable power modules:

· 500 W AC PoE power module

· 650 W DC PoE power module

· 1150 W AC PoE power module

· 1000 W AC PoE power module (applicable in V200R013C00 and later versions)

Item

Description

Memory (RAM)

1 GB

Flash

512 MB in total. To view the available flash memory size, run the display version command.

Power supply surge protection

  • Using 500 W AC or 1000 W AC power modules: ±6 kV in differential mode, ±6 kV in common mode
  • Using 650 W DC or 1150 W AC power modules: ±2 kV in differential mode, ±4 kV in common mode

Dimensions (H x W x D)

44.4 mm x 442.0 mm x 420.0 mm (1.75 in. x 17.4 in. x 16.5 in.)

When 1150 W power modules are installed, they stretch out from the chassis. Therefore, the total depth of the switch changes to 507.3 mm (19.97 in.).

Weight (with packaging)

8 kg (17.64 lb)

Stack ports

Any 10GE SFP+ or 40GE QSFP+ ports

Ports on the 2-port QSFP+ rear stack card

RTC

Supported

RPS

Not supported

PoE

Supported

Rated voltage range

100 V AC to 240 V AC, 50/60 Hz

-48 V DC to -60 V DC

Maximum voltage range

90 V AC to 264 V AC, 47 Hz to 63 Hz

-38.4 V DC to -72 V DC

Maximum power consumption (100% throughput, full speed of fans)

  • Using 650 W DC or 500 W AC power modules
    • Not providing the PoE function: 68.3 W (without card)
    • 100% PoE loads: 925 W (system power consumption: 185.8 W, PoE: 739.2 W, without card)
  • Using 1150 W AC or 1000 W AC power modules
    • Not providing the PoE function: 68.3 W (without card)
    • 100% PoE loads: 1733 W (system power consumption: 293 W, PoE: 1440 W, without card)
Typical power consumption (30% of traffic load)
  • Tested according to ATIS standard
  • EEE enabled
  • No PoE power consumption

50.1 W (without card)

Previous: Huawei S5730 Series S5730-68C-HI 48Port Gigabit Ethernet Swi...

next: Huawei S5730-48C-PWR-SI-AC 24 Port Gigabit 8x 10G SFP+ Layer...

Top

Cisco network switch,Huawei switch,Cisco Router, Huawei router,NEW used Cisco comparison, Huawei AP WeChat Code

Copyright © 2018 - 2019 Shenzhen Bo-Net Technology Co., Ltd. All Rights Reserved.